TOWNSEND LAKE WEST GREY ONTARIO COVERED PORCH BUILD | JCB AND SONS
We built this new covered porch on this cottage to allow access from the front of the cottage to the back deck overlooking Townsend Lake. The foundation piers were created using BF20 Bigfoots with 10" quick-tubes installed 4'-0" below grade to ensure adequate frost protection.
The piers were filled with cement and 2 pieces of 15mm rebar to make strong supports as well as carport saddles were installed to anchor the new structure to the base.
Deck building is a form of trim carpentry so all corners are mitered even on the framing.
Galvanized joist hanger brackets were used with galvanized joist hanger nails to get flush beams keeping the framing off of the ground even at the lowest end.
Deck flashing was used on the top of all the framing to ensure the top of the framing will not rot.
Kreg Jigs hidden deck fastner system was used to hide all of the screws used to fasten the decking.
All of the roof framing stayed exposed so the rafters and strapping were all rounded over and a coat of Sikkens Stain was used to weather proof it prior to installing.
Steel roofing was used on the 2 ends and polycarbonate x-ligh was used to keep the porch roof nice and bright. Strapping was ran on 12" centres to give lots of support to the x-light.
The wooden structural beam was clad in pine barn board and finished with a coat of Sikkens Cedar Stain.
We installed new vented soffit on the ends to tie neatly into the home and clad all the fascia boards in aluminum fascia we custom bent on site.
We installed 2"x4" rails with a 2"x6" handrail which received a nice big round over to create the railings for the porch. The homeowner has plans for his own spindles and is looking after that himself.
WEST GREY ONTARIO MASTER BEDROOM WALK IN CLOSET BUILD | JCB AND SONS
West Grey Ontario Master Bedroom Walk In Closet Build | JCB & SONS. This 1978 home needed a larger MasterBedroom, we removed a dividing wall between two bedrooms, removed textured ceilings and finished out the drywall with a level 5 skim coat to leave perfectly smooth ceilings. Installed new 3/4" Maple Hardwood Flooring and Completely overhauled the closets with completely custom build cabinetry, wardrobe, builtins, drawers, and custom made mirrored doors for the closets. We also had a new high efficiency furnace system installed in this home with new duct work and an HRV to keep this bedroom as well as the whole house the perfect temperature year round.
All of the Cabinets were full 3/4" Plycore Maple Veneer Construction.
The face frames were all built using a very traditional mortise and tenon joint. Making a very durable quality connection of the styles and rails.
These are the Tenons that will make the connection with all the mortises.
All of the drawer boxes were made using soft maple and blind dovetails cut onsite at our shop.
We used all solid Hard Maple for the face frames and classic styled raised panel doors which were also all milled and built in our shop.
Milling the styles and rails on our spindle molder.
The completed cabinets where than sprayed with 3 coats of Lacquer to provide a very high quality durable finish.
These 8' Maple mirrored doors were installed on high quality Johnson hardware and glide effortlessly as sliding doors should.
We also built a completely maple wardrobe to be part of all the cabinets and create some fantastic hanging storage with adjustable wire rack shelving.
All of the shelving received solid maple nosing verses the typical edgebanding you see on cabinet shelving.
The drywall beam used to support the ceiling after removing a dividing wall was a great place to use some Trim Tex Step-A-Bull Corner beads for a great detail.
The closets also received Maple built ins in the closets on top of the adjustable wire rack shelving and they also received full face frames.
DINING ROOM REMODEL FOR LISTOWEL DAIRY QUEEN | JCB AND SONS
Custom Millwork for
| JCB & SONS. We recently completed a dining room remodel for
. We spent a few days on site installing new table tops on all the booths. We also added a new high bar with chairs. All of the new counters and table tops were custom made at
.
The new bar top mounts as well as the new custom made table legs were made for us by
. They were Powder coated by
disconnected and reconnected the Pop Machine while we changed out the Pop Cabinet which was custom made by us with 3/4" Ply Core Maple Veneer with a lacquer finish. We made a solid 1-1/2" Fir Plywood top which was clad in Stainless Steel made by
and was welded by
.
We used 4 of the original benches from the booths and connected them to make two new longer benches to go with the new tables. We installed the benches on a new Ply-Core Maple Veneered custom drawer base creating some much needed storage space for the restaurant. We also used a push to open drawer slide to eliminate handles sticking out into the traffic flowing through the restaurant.
We spent a lot of time in the design stage to ad some more seating as well as more comfortable seating to the restaurant. Garbage cans were incorporated into the pop cabinet as well as a place for the high chairs for young children.
We spent quite a bit of time with the owner Amy of Dairy Queen designing this project to fit her specific needs. Trying to incorporate the colours of Dairy Queen, the flow of the restaurant and more seating as well as comfortable seating for her dining room.
